View TS6001BIG325TP_4603981.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ts6001 page 1 ? 2012 touchstone semiconductor, inc. all rights reserved. features ? improved electrical performance over max6025 ? initial accuracy: 0.08 % (max) C ts6001 a 0. 16 % (max) C ts6001 b ? temperature coefficient: 7 ppm/c (max) C ts6001 a 10 ppm /c (max) C ts6001 b ? quiescent supply current: 35 a (max) ? low supply current change with v in : 0. 1 a/v ? outpu t source/ sink current: 500 a ? low drop out at 50 0a load current: 75 mv ? load regulation: 30 ppm /m a ? line regulation : 10ppm /v ? stable with c load up to 2200p f applications battery - operated equipment data acquisition systems hand - held equipment smart industrial transmitters industrial and process - control systems precision 3v/5v systems hard - disk drives description the ts6001 is a 3 - terminal, series - mode 2.5 - v precision voltage reference and is a pin - for - pin, identical to the max6025 voltage reference with improved electrical performance . t he ts6001 consumes only 31 a of supply current at no - load, exhibits an initial output v o ltage accuracy of less than 0.08 %, and a low output volt age temperature coefficient of 7 ppm/c. in addition, the ts6001 s output stage is stable for all capacitive loads to 2200pf and is capable of sinking and sourcing load currents up to 500 a . since the ts6001 is a series - mode voltage reference, its supply current is not affected by changes in the applied supply voltage unlike two - terminal shunt - mode references that require an external resistor. the ts6001 s small form factor and low supply curr ent operation all combine to make it an ideal choice in low - power, precision applications. the ts6001 is fully specified over the - 40c to +85c temperature range and is available in a 3 - pin sot23 package. a 7ppm/ c, 0.08% p recision +2.5v voltage reference in sot23 typical applicat ion circuit temperature drift - c output voltage - volt - 40 - 15 10 35 85 60 2.4995 2.4990 three typical devices device #1 device #2 device #3 2.5005 2.5000 2.5010 output voltage temperature drift
ts6001 page 2 ts6001ds r1p0 rtfds absolute maximum rat ings in to gnd ................................ ............................... - 0.3v to +13.5v out to gnd ................................ ................................ .. - 0.3v to 7v short circuit to gnd or in (v in < 6v ) ............................. continuous output short circuit to gnd or in (v in 6v) .............................. 60s continuous power dissipation (t a = +70c) 3 - pin sot23 ( d erate at 4.0mw/c above +70c) ......... 320mw operating temperature range ................................ - 40c to +85c storage temperature range ................................ . - 65c to +150c lead temperature (s oldering, 10s) ................................ ..... +300c electric al and thermal s tresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. these are stress ratings only and functional operation of the device at these or any other condition beyond those indicated in the operational sections of the specifications is not implied. exposure to any absolute maximum rating conditions for extended periods may affect device reliab ility and lifetime . package/ordering information order number part marking carrier quantity ts6001aig325tp aag tape & reel ----- ts6001aig325t tape & reel 3000 TS6001BIG325TP aah tape & reel ----- ts6001big325t tape & reel 3000 lead - free program: touchstone semico nductor supplies only lead - free packaging. consult touchstone semiconductor for products specified with wider operating temperature ranges.
ts6001 ts6001ds r1p0 page 3 rtfds electrical character istics v in = +5v, i out = 0, t a = t min to t max , unless otherwise noted. typical values are at t a = +25c. see note 1 . parameter symbol conditions min typ max units output output voltage v out t a = +25 c ts6001 a 2.498 2.500 2.50 2 v - 0. 08 0. 08 % ts6001 b 2.49 6 2.500 2.50 4 v - 0. 16 0. 16 % output voltage t emperature coefficient (see note 2) tc v out 0 c t a +8 5 c ts6001 a 2 7 ppm/c - 40 c t a +8 5 c 2.5 10 0 c t a +8 5 c ts6001 b 3 10 - 40 c t a +8 5 c 4 15 line regulation ( v out /v out ) / v in (v out + 0.2v) v in 12.6v 10 30 ppm /v load regulation ( v out /v out ) / i out sourcing 0 i out 500 a 30 240 ppm/ma sinking - 500a i out 0 70 320 dropout voltage (see note 3) v in - v out i out = 500 a 75 150 mv out short - circuit current i sc v out short to gnd 4 ma v out short to in 4 temperature hys teresis ( see note 4 ) 100 ppm long - term stability ( see note 5) v out / time 168 hr at t a = +25 c 75 ppm/ 1 68 hr dynamic noise voltage e out f = 0.1hz to 10hz 50 v p - p f = 10hz to 10khz 75 v rms ripple rejection v out / v in v in = 5v 100mv, f = 120hz 8 2 db turn - on settling time t r to v out = 0.1% of final value, c out = 50 pf 340 s capacitive - load stability range c out see note 6 0 2 2 00 p f input supply voltage range v in gua ranteed by line - regulation test v out + 0.2 12.6 v quiescent supply current i in 31 35 a change in supply current i in /v in (v out + 0.2v) v in 12.6v 0.1 0. 2 a/v note 1: all devices are 100% production tested at t a = +25c and are guaranteed by characterization for t a = t min to t max , as specified. note 2: temperature coefficient is measured by the box method; i.e., the maximum v out is divided by the maximum t . note 3 : dropout voltage is the minimum input voltage at which v out changes 0.2% from v out at v in = 5.0v. note 4 : temperature h ysteresis is defined as the change in the +25c output voltage before and after cycling the device from +25c to t min to +25c and from +25c to t max to +25c . note 5 : reference long - term drift or stability listed in the table is an intermediate result of a 1000 - hour evaluation. soldered onto a printed circuit board (pcb), voltage references exhibit more drift early in the evaluation because of assembly - induced different ial stresses b etween the package and the pcb. note 6 : not production tested; g uaranteed by design.
ts 6001 page 4 ts6001ds r1p0 rtfds line regulation output voltage change - ppm supply voltage - volt - 40 0 80 120 t a = - 40 c t a = +8 5c 40 load current - m a t a = +85 c load regulation - 0.5 0.5 0.25 - 0.25 - 160 - 80 160 0 80 source current - a dropout voltage - v dropout voltage vs source current 400 800 0 1000 600 200 0 0.1 0.4 0.2 0.3 time - hours output voltage change - ppm 0 t a = +25c t a = +8 5c t a = - 40 c 8 12 2 14 10 4 6 t a = - 40 c typical performance characteristics v in = +5v; i o ut = 0m a ; t a = +25 c, unless otherwise noted. t a = +2 5c t a = +25 c three typical devices device #1 0 42 84 168 126 2.5050 output voltage - volt device #2 device #3 long - term output voltage drift temperature drift - c output voltage - volt - 40 - 15 10 35 85 60 2.4995 2.4990 three typical devices device #1 device #2 device #3 2.5005 2.5000 2.5010 output voltage temperature drift output voltage error - % number of units 0 0.02 2 0 7 6 9 output voltage histogram - 0.02 0.04 4 8 5 3 1 2.5025 2.5000 2.4950 2.4975
ts6001 ts6001ds r1p0 page 5 rtfds power supply rejection vs frequency 0.1hz to 10hz output noise v out(n) 10 v/div output impedance - ? frequency - hz 1 10 1k 0.1 100 10k 0.1 1 100 1m 10k 1s/div 200 s/div power - on transient response input 2v/div supply current vs input voltage supply curent - a input voltage - volt 20 28 36 40 8 12 2 14 32 10 supply current vs temperature temperature - c supply curent - a v cc = +2.5v, +5.5v v cc =+12.5v - 40 - 15 10 35 85 60 25 35 20 30 40 output impedance vs frequency output 1v/div v cc =+7.5v 4 6 24 typical performance characteristics v in = +5v; i o ut = 0m a ; t a = +25 c, unless otherwise noted. 46 v pp power supply rejection C mv/v frequency - hz v cc =+5.5v 0.25v 1 10 0.01 100 100 1k 10k 1m 100k 0.1
ts 6001 page 6 ts6001ds r1p0 rtfds line transient response 2 s/div 10 s/div i out 1m a/div output 200mv/div v in =5v 0.25v, ac - coupled v in 200m v/div output 100mv/div large - signal load transient response i out = 0ma 1ma 0ma, ac - coupled 10 s/div small - signal load transient response i out 50 a/div output 20mv/div i out = 0 a 50 a 0 a, ac - coupled typical performance characteristics v in = +5v; i o ut = 0m a ; t a = +25 c, unless otherwise noted.
ts6001 ts6001ds r1p0 page 7 rtfds pin functions pin name function 1 in supply voltage input 2 out +2.5v output 3 gnd ground description/ theory of operation the ts6001 incorporates a precision 1.25 - v bandgap referen ce that is followed by an output amplifier configured to amplify the base bandgap output voltage to a 2.5 - v output. the design of the bandgap reference incorporates proprietary circuit design techniques to achieve its low temperature coefficient of 7 ppm/c and initial output voltage accuracy less than 0.08 %. the design of the output amplifiers frequency compensation does not require a separate compensation capacitor and is stable with capacitive loads up to 2200pf. the design of the output amplifier also incorporates low headroom design as it can source and sink load currents to 500a with a dropout v oltage less than 1 00mv. applications informa tion power supply input bypass capacitance if there are other analog ics within 1 to 2 inches of the ts6001 with their own bypass capacitors to gnd, the ts6001 would not then require its own bypass capacitor. if this is not the case, then it is considered good analog circuit engineering practice to place a 0.1f ceramic capacit or in as close proximity to the ts6001 as practical with very short pcb track lengths. output/load capacitance considerations as mentioned previously, the ts6001 do es not require a separate, external capacit or at v out for transient response stability as it is stable for capacitive loads up to 22 00pf . f or improved load regulation transient response , the use of a capacitor at v out helps to reduce output voltage overshoot/ undershoot to transient load current conditions . figure 1 illustrates the ts6001s tran sient load regulation performance with c load = 0pf to a 50 - a transient upon a 175 - a steady - state load current. peak transients are approximately 20mv and th e ts6001 settles in less than 8 s. as shown in figure 2, add ing a capacitive load reduces peak transients at the expense of settling time. in this case, the ts6001s output was loaded with c load = 1000pf and subjected to the same transient load current profile. peak transients were reduced to less than 10mv and the ts6001 settled in less than 10s. figure 2 : ts6001 transient load regulation response, c load = 1000pf i out 50 a/div output 20mv/div i out = 175 a 22 5 a 175 a figure 1 : ts6001 transient load regulation response, c load = 0pf i out = 175 a 22 5 a 175 a i out 50 a/div output 20mv/div
ts6001 page 8 ts6001 ds r1p0 rtfds supply current the ts6001 exhibits excellent dc line regulation as its supply current changes slightly as a function of the appli ed supply voltage . because of a unique bias loop design , the change in its supply current as a function of supply voltage (its i in /v in ) is less than 0. 1a/v. since the ts6001 is a series - mode reference, load current is drawn from the supply voltage only when required. in this case, circuit efficiency is maintained at all appli ed supply voltages. reducing power dissipation and extending battery life are the net benefits of improved circuit efficiency. when the applied supply voltage is less than the minimum specified input voltage of the ts6001 ( for example, during the power - up or cold - start transition ), the ts6001 performs an internal calibration routine and can draw up to 200 a above its nominal , steady - state supply current. this internal calibration sequence also dominates the ts6001s turn - on time. to ensure reliable power - up behavior, the input power source must have sufficient reserve power to provide the extra supply current drawn during the power - up transition. voltage reference turn - on time with a (v in C v out ) voltage differential larger than 200mv and i load = 0ma, the ts6001s typical combined turn - on and settling time to within 0.1% of its 2.5v final value is approximately 340 s. output voltage hysteresis reference output voltage thermal hysteresis is the change in the references +25c output voltage a fter temperature cycling from +25 c to +85 c to +25 c and from +25 c to - 40 c to +25 c. thermal h ysteresis is caused by differential package stress impressed upon the ts6001s internal bandgap core transistors and depends on whether the reference ic was previously at a higher or lower temperature . at 1 0 0 ppm, t he ts6001s typical temperature hysteresis is equal to 0. 25 mv with respect to a 2.5v output voltage. connecting two or more ts6001s in stacked v out arrangements in many applications, it is desired to combine the outputs of two or more precision voltage references, especially if the combined output voltage is not available or is an uncommon output voltage. one such technique for combining (or stacking) the output s of precision voltage refere nces is illustrated in figure 3 . in this example and powered by an unregulated supply voltage (v in +5.2v), two ts6001 - 2.5 precision voltage references are used. the gnd terminal of refa is connected to the out terminal of re fb. this connection produces two output voltages, v refout1 and v refout2 , where v refout1 is the terminal voltage of refb and v refout2 is v refout1 plus the out terminal voltage of refb. by implementing this stacked arrangement with a pair of ts6001 - 2.5s , v re fout2 is 5v and v refout1 is 2.5v. although the ts6001 - 2.5s do not specifically require input bypass capacitors, it is good engineering practice to bypass both reference s from v in to the global gnd terminal (at refb) . if either or both reference ics are required to drive a load capacitance, it is also good engineering practice to route the load capacitors return lead to each references corresponding refs gnd terminal. the circuits minimum input supply voltage, v in , is determined by v refout2 and refbs dropout voltage (75m v, typically). how to configure the ts6001 into a general - purpose current source in many low - voltage applications, a general - purpose current source is needed with very good line regulation . the t s6001 - 2.5 can be configured as a grounded - load , floating current source as shown figure 4 . in this example, the ts6001 - 2.5s output voltage is bootstrapped across an external resistor (r1 + p1) which, in turn, sets the output current. the circuits total o utput current is i out = i set +i qsc where i qsc is the ts6001 supply current (up to 35a). for figure 3 : connecting two ts6001 - 2.5s in a stacked v refout arrangement
ts6001 ts6001ds r1p0 page 9 rtfds improved output current accuracy , i set should be at least 10 times i qsc . a negative, precision voltage reference without precision resistors when using current - output dacs, it is oftentimes desired that the polarity of the output signal voltage is the same as the external referenc e voltage. there are two conventional techniques used to accomplish this objective: a) inverting the full - scale dac output voltage or b) converting a current - output dac into a voltage - switching dac. in the first technique, an op amp and pair of precision r esistors would be required because the dacs output signal voltage requires re - inversion to match the polarity of the external reference voltage. the second technique is a bit more involved and requires converting the current - output dac into a voltage - swit ching dac by driving the dacs vref and iout terminals in reverse. additional components required are two precision resistors, an op amp, and an external voltage reference, typically a 1.25 - v reference. if the 1.25 - v full - scale output voltage requires scal ing to a 2.5 - v or a 5 - v full scale, then a second op amp and pair of precision resistors would be necessary to perform the amplification. to avoid the need for either re - inversion of the current - switching dacs output voltage or amplifying the voltage - swi tching dacs output voltage, it would then be desired to apply a negative voltage reference to the original current - switching dac. in general, any positive voltage reference can be converted into a negative voltage reference using pair of matched resistors and an op amp configured for inverting mode operation. the disadvantage to this approach is that the largest single source of error in the circuit is the relative matching of the resistors used. the circuit illustrated in figure 5 avoids the need for multiple op amps and well - matched resistors by using an active integrator circuit. in this circuit, the voltage references output is used as the input signal to the integrator. because of op amp loop action, the integrator adjusts its output voltage to establish the correct relationship between the references out and gnd ter minals (= v ref ). in other words, the output voltage polarity of the integrator stage is opposite that of the references output voltage. the 2200pf capacitor at th e output of the ts6001 is optional and the resistor in series with the output of the op amp should be empirically determined based on the amplifier choice and whether the amplifier is required to drive a large capacitive load. rail - to - rail output op amps used for the integrator stage work best in this application; however, these types of op amp s require a finite amount of headroom (in the millivolt range) when sinking load current. therefore, good engineering judgment is always recommended when selecting t he most appropriate negative supply for the circuit. how to use the ts6001 in a high - input voltage floating current source by adopting the technique previously shown in figure 2 , the basic floating current source circuit can be adapted to operate at much higher supply voltages beyond the supply voltage rating of the ts6001 - 2.5 by adding a discrete n - channel jfet. as shown in f igure 6 , the jfet acts as a supply voltage regulator since its source voltage will always be 2.5v higher than v sy . the circuit minimizes reference ic self - heating because the jfet and the 2n3904 npn transistor carry the load current. this circuit can operate up to +35v and is determined by the bv ds breakdown voltage of the external jfet. figure 4 : a low - power, general - purpose current source. figure 5: how to co n vert a v ref to a C ref without precision resistors.
ts6001 page 10 ts6001 ds r1p0 rt f ds for exa mple, if v sy is 0v, then the upper input supply voltage level for the circu it is 35v. with a 2.1k load and the ts6001s supply current of 3 5 a (max) , this circuit supplies approximatel y a 1.2 3 - ma current to the load. in many current source applications, the possibility of an output short - circuit condition - whether transient or sustained - exists. i t is recommended to test thoroughly for either scenario to prevent the possibility that the ts6001 would be exposed to a total voltage from its in terminal to gnd terminal higher than its absolute maximum rating of 13.5v. boosting the ts6001s output current drive while the ts6001 is capable of sourcing up to 500a with excellent load regulation, there are applications where tight load regulation is required at much higher output load currents. by adding a general - purpose, industry - standard pnp transistor and one re sistor to the ts6001s basic configuration as shown in figure 7 , increasing a precision references output source current drive is straightforward. using a 2n2905 pnp transistor and a 1.5k? resistor, the ts6001 is able to maintain excellent load regulation while sourcing load currents up to 150ma. if the application circuit is designed to operate across a wide temperature range, it is recommended that circuit performance is thoroughly evaluated across the pnp transistors beta ( , or current gain ) distribution. when the pnp transistors current gain is a minimum, the increase in base current must be absorbed by the ts6001 for a given load current. for higher output load currents, higher output power pnp transistor s can be used so long as good ther mal management techniques are applied and transistor current - gain vs ambient temperature behavior is evaluated . figure 6 : using the ts6001 - 2.5 in a high - input voltage floating current source. figure 7 : boosting the ts6001s output current
ts6001 ts6001ds r1p0 page 11 rtfds generating positive and negative low - power voltage reference s the circuit in figure 8 uses a cd4049 hex inverter and a few external capacitors as the power supply to a dual - supply precision op amp to form a 2.5v precision, bipolar output voltage reference around the ts6001 . the cd4049 - based circuit is a discrete charge pump voltage do ubler /inverter that generates 6 v supplies for any precision, micropower op amp with v os and tcv os specifications consistent with the ts6001s initial accuracy and output voltage drift performance . figure 8 : generating positive and negative 2.5v references from a single +3v or +5v supply .
ts6001 page 12 touchstone semiconductor, inc. ts6001 ds r1p0 630 alder drive, milpitas, ca 95035 rt f ds +1 (408) 215 - 1220 ? www.touchstonesemi.com package outline draw ing 3 - pin sot23 package outline drawing (n.b., drawings are not to scale) information furnished by touchstone semiconductor is believed to be accurate and reliable. however, touchstone semiconductor does not assume any responsibil ity for its use nor for any infringements of patents or other rights of third parties that may result from its use , and all information provided by touchstone semiconductor and its suppliers is provided on an as is basis, without warranty of any kin d . touc hstone semiconductor reserves the right to change product specifications and product descriptions at any time without any advance notice. no license is granted by implication or otherwise under any patent or patent rights of touchstone semiconductor. touchstone semiconductor assumes no liability for applications assistance or customer product design. customers are responsible for thei r products and applications using touchstone semiconductor components. to minimize the risk associated with customer pro ducts and applications, customers should provide adequate design and operating safeguards. trademarks and registered trademarks are the property of t heir respective owners. 1 . 0 3 m a x 0 . 8 9 m i n 3 . 0 4 m a x 2 . 8 0 m i n 1 . 1 2 m a x 0 . 8 9 m i n 0 . 1 0 0 m a x 0 . 0 1 3 m i n 0 . 3 m i n 0 . 5 m a x 2 . 6 4 m a x 2 . 1 0 m i n 0 . 9 4 m a x 0 . 8 8 m i n 0 . 5 4 m a x 0 . 4 8 m i n 1 . 4 0 m a x 1 . 2 0 m i n 0 . 2 0 m a x 0 . 0 8 m i n 0 . 6 8 5 m a x 0 . 4 0 6 m i n 0 . 2 5 0 . 4 1 m a x 0 . 2 1 m i n 0 ' C 8 ' 2 1 1 d o e s n o t i n c l u d e m o d e f l a s h , p r o t r u s i o n s o r g a t e b u r n s . m o d e f l a s h , p r o t r u s i o n s o r g a t e b u r n s s h a l l n o t e x c e e d 0 . 1 2 7 m m p e r s i d e 2 d o e s n o t i n c l u d e i n t e r - l e a d f l a s h o r p r o t r u s i o n s . i n t e r - l e a d f l a s h a n d p r o t r u s i o n s s h a l l n o t e x c e e d 0 . 1 2 7 m m p e r s i d e . 3 . d i e i s f a c i n g u p f o r m o l d d i e a n d t r i m - f o r m . 4 . l e a d s p a n / s t a n d o f h i g h / c o p l a n a r i t y a r e c o n s i d e r e d a s s p e c i a l c h a r a c t e r i s t i c . 5 . a l l s p e c i f i c a t i o n s r e f e r d j e d e c t o - 2 3 6 a b e x c e p t f o r l e a d l e n g t h d i m e n s i o n . 6 . c o n t r o l l i n g d i m e n s i o n i n ( m m ) 0 . 1 0 m a x n o t e : 0 . 1 6 m a x 0 . 0 8 m i n 0 . 2 0 m a x 0 . 0 8 m i n 0 . 5 0 m a x 0 . 3 0 m i n 0 . 4 5 m a x 0 . 3 0 m i n 1 0 ' t y p 1 0 ' t y p g a u g e p l a n e 2 . 0 5 m a x 1 . 7 8 m i n 0 . 2 7 r e f

▲Up To Search▲

Price & Availability of TS6001BIG325TP

	To Download TS6001BIG325TP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .